HP2-Z26 - Fast Track - Implementing HP Network Technologies

Go back to HP

Example Questions

A VLAN is connected to an HP Comware hybrid port. What can a network administrator use to assign a device to the VLAN? (Select two.) What are HP Cloud Maps? Which HP redundancy features are supported by both HP Provision and HP Comware switches? (Select two.) A network administrator is expanding part of the data center in a hospital network. Three new racks of equipment need to be added, with an HP Comware 5820 series switch at the top of each rack. The Comware 5820 series switch needs to connect back to two coreComware 12600 switches using 10Gb connections. The distance between the three racks and the Comware 12500 switches is approximately 40 meters; however, the network administrator is concerned about electromagnetic and other types of interferences to electrical signals Which solutions protect against interference and are cost-effective for this scenario? (Select two.) Refer to the partial command output. <Comware> display link-aggregation verbose bridge-aggregation 2 <-output omitted-> Aggregation Interface: Bridge-Aggregation2 Aggregation Mode: Dynamic Loadsharing Type: Shar System ID: 0x8000, 000f-e267-6c6a Local: Port Status Priority Oper-Key Flag ------------------------------------------------------------------------- GE1/0/3 S 32768 2 {AG} GE1/0/4 S 32768 2 {AG} Remote: Actor Partner Priority Oper-Key SystemID Flag --------------------------------------------------------------------------- GE1/0/3 32 32768 2 0x8000, 000f-e267-57ad {AG} GE1/0/4 26 32768 2 0x8000, 000f-e267-57ad {AG} Based on this output, which statement is true? A network administrator is examining the routing table on an HP Comware switch. The network administrator sees two routes. 10.1.1.0/24, with the same neighbor's address (10.1.1.1). What would create this result? A company has two buildings that are 15 meters apart. The company needs to connect the buildings' networks. The CFO does not want the cost of installing fiber between the two buildings and thus is exploring wireless options. If the company selects an 802 11n wireless solution, which wireless mode should they use? Which modules provide connectivity for blade servers installed in the HP BladeSystem c-Class enclosure to external switches? (Select two.) A network administrator configures the following information on an HP Provision switch: Provision(config)# spanning tree Provision(config)# spanning tree instance 0 priority 2 Based on this information, what is the priority assigned to this switch for instance 0? Based on the default precedence used to rank routing protocols in HP Comware switches, if a default route (0.0.0.0/0) is learned from multiple routing protocols, which source would the Comware operating system prefer? A network administrator has installed IMC and the appropriate licenses. The network administrator is attempting to import the HP Comware and HP Provision switches into IMC but is experiencing problems importing the Comware switches. The network administrator verifies the SNMPv2c configuration on both sets of switches and the SNMP configuration in IMC. The SNMP parameters are correct. What is the cause of the import problem? Which configuration tool do HP Provision switches support that HP Comware switches do not support? Which Software-Defined Network (SDN) layer includes HP Provision and HP Comware switches? What are the default logging properties for an HP Comware switch? (Select two.) Which standards do HP products support for Power over Ethernet (PoE)? (Select two.) Which standards do HP products support for Power over Ethernet (PoE)? Which IMC agent starts and stops the IMC server and allows a network administrator to view the status of the IMC processes? A network administrator is implementing a network with HP Comware and HP Provision switches. When the network administrator boots the switches for the first time, what are the factory default settings of all of the switches in the network? (Select two.) Which HP information management product manages large data volumes, is known for fast query performance, and is available on HP DL380 rack-mount servers? A network administrator receives a new HP ProVision switch and notices that the software version running on the switch is older than what is currently used in the network. The network administrator copies an updated version of the operating system from the new switch's USB port to the secondary flash location. The network administrator then executes the following command: ProVision# boot system flash secondary The switch reboots using the new operating system. However, when the network administrator turns off the switch and turns it back on, the switch boots from the old operating system. Which solution should the network administrator use to fix the problem? A network administrator is building two IRF domains: One domain for the two distribution layer switches One domain for the access layer switches Each access layer switch should have a connection to each distribution layer switch. In this design, how many access switches can the administrator have in the access layer IRF domain before spanning tree is required to remove loops between the two IRF domains? Which HP Provision and HP Comware commands restore a configuration file from a TFTP server to the switches' flash? (Select two.) Which HP Provision switch command lists the operating system that is currently loaded? Which statements are correct about HP StoreOnce Backup? (Select two.) A network administrator has two distribution layer switches and four access layer switches. The network administrator is constantly resolving spanning tree problems and is looking for an alternative solution that provides redundancy and no spanning tree. Which solutions meet the network administrator’s requirements? (Select two) What are factory default configuration settings of the HP MSM access points (APs)? (Select two.) Which item is different between the IEEE 802.3z and 802.3ae standards? A network administrator has an HP Comware switch that is configured with OSPF. The network administrator views the routing table and sees that a default route was learned from an OSPF neighbor (10.1.1.1). However, the network administrator wants to override this action and use a different neighbor (10.1.1.2) for the default route. The network administrator configures this command: [Comware] ip route-static 0.0.0.0 0 10.1.1.2 After configuring the command, the network administrator examines the routing table and notices that the original neighbor's default route is still in the routing table, but the static route is missing. What is the cause of this problem? Which HP technology includes server provisioning, monitoring, diagnostics, and support? A network administrator is connected to the console of an HP Comware switch when these messages display: %Apr 26 12:06:04:929 2013 Comware-1 DEV/1/BOARD INSERTED: Trap 1.3.6.1.4.1.25506.8.35.12.1.9<hh3cBoardInserted>: chassisIndex is 0, slotIndex 0.2 %Apr 26 12:06:05:110 2013 Comware-1 DEV/4/BOARD STATE FAULT: Board state changes to FAULT on Chassis 0 Slot 2, type is unknown. %Apr 26 12:06:57:423 2013 Comware-1 DEV/1/BOARD STATE CHANGES TO NORMAL: Trap 1.3.6.1.4.1.25506.8.35.12.1.11<hh3cBoardNormal>: chassisIndex is 0, slotIndex 0.2 %Apr 26 12:06:57:623 2013 Comware-1 DEV/4/BOARD STATE NORMAL: Board state changes to NORMAL on Chassis 0 Slot 2, type is MAIN_BOARD_TYPE_32C. %Apr 26 12:07:02:222 2013 Comware-1 IFNET/4/LINK UPDOWN: Ten-GigabitEthernet2/0/25: link status is UP %Apr 26 12:07:02:377 2013 Comware-1 IFNET/4/LINK UPDOWN: Ten-GigabitEthernet2/0/26: link status is UP %Apr 26 12:07:02:722 2013 Comware-1 HA/4/HA_LOG:Batch backup(s) of slave board(s) in slot 2 started. %Apr 26 12:07:03:140 2013 Comware-1 OPTMOD/4/MODULE_IN:Slot=2; Ten-GigabitEthernet2/0/25: The transceiver is 10G_BASE_STACK_SFP. %Apr 26 12:07:03:300 2013 Comware-1 OPTMOD/4/MODULE_IN:Slot=2; Ten-GigabitEthernet2/0/26: The transceiver is 10G_BASE_STACK_SFP. Based on this information, what has just occurred? A network administrator is expanding part of the data center in a hospital network. Three new racks of equipment need to be added, with an HP Comware 5820 series switch at the top of each rack. The Comware 5820 series switch needs to connect back to two core Comware 12500 switches using 10Gb connections. The distance between the three racks and the Comware 12500 switches is approximately 40 meters; however, the network administrator is concerned about electromagnetic and other types of interferences to electrical signals. Which solutions protect against interference and are cost-effective for this scenario? (Select two.) Which statements are true about the Network Time Protocol (NTP)? (Select two.) A network administrator enables debug to troubleshoot an OSPF adjacency on an HP Comware switch. The network administrator then disables and then re-enables an interface connected to another switch running OSPF. After waiting for a few minutes, no output displays on the console. Which action must the network administrator take to resolve this problem? Which HP Comware command saves the startup configuration file to a TFTP server? A network administrator has an HP Comware switch that is configured with OSPF. The network administrator views the routing table and sees that a default route was learned from an OSPF neighbor (10.1.1.1). However, the network administrator wants to override this action and use a different neighbor (10.1.1.2) for the default route. The network administrator configures this command: [Commware] ip route-static 0.0.0.0 0 10.1.1.2 After configuring the command, the network administrator examines the routing table and notices that the original neighbor's default route is still in the routing table, but the static route is missing. What is the cause of this problem? Which console cable is used on an HP Comware switch? What is the default state of spanning tree on HP Comware switches? A network administrator is setting up OSPF between an HP Provision and HP Comware switch. Once the configuration is finished, the network administrator sees log messages in the Comware session about the successful establishment of the adjacency. However, the network administrator does not see similar messages on the Provision console. How can the network administrator see these log messages about the new OSPF adjacencies on the Provision console? Before upgrading networking equipment like switches, a network administrator should first perform some important preparation tasks. What should the network administrator include in the creation of an upgrade policy? (Select two.) What are the participants in the 802 1X authentication process? (Select two.) Refer to the HP Comware configuration. interface vlan 1 ip address 10.1.1.1 255.255.255.0 quit interface vlan 2 ip address 10.1.2.1 255.255.255.0 quit interface loopback 1 ip address 1.1.1.1 255.255.255.255 quit router-id 1.1.1.1 area 0 network 1.0.0.0 0.255.255.255 network 10.1.1.0 0.255.255.255 The network administrator set up VLAN 2 as a management VLAN. This VLAN should not be included in the OSPF routing process. Now only directly connected network administrators in VLAN 2 can manage the switch. How should the network administrator solve this problem? A network administrator is building two IRF domains: - One domain for the two distribution layer switches - One domain for the access layer switches Each access layer switch should have a connection to each distribution layer switch. In this design, how many access switches can the administrator have in the access layer IRF domain before spanning tree is required to remove loops between the two IRF domains? What is the function of HP Intelligent Provisioning? A network administrator receives a new HP Provision switch and notices that the software version running on the switch is older than what is currently used in the network. The network administrator copies an updated version of the operating system from the new switch's USB port to the secondary flash location. The network administrator then executes the following command: ProVision # boot system flash secondary The switch reboots using the new operating system. However, when the network administrator turns off the switch and turns it back on, the switch boots from the old operating system. Which solution should the network administrator use to fix the problem? A company has two buildings that are 15 meters apart. The company needs to connect the buildings' networks. The CFO does not want the cost of installing fiber between the two buildings and thus is exploring wireless options. If the company selects an 802.11n wireless solution, which wireless mode should they use? Refer to the link aggregation between two HP switches. ProVision(config)# interface A1-A2 lacp passive ProVision(config)# vlan 10 tagged trk1 [Comware] interface bridge-aggregation 1 [Comware-Bridge-Aggregation1] link-aggregation mode dynamic [Comware-Bridge-Aggregation1] quit [Comware] interface g1/0/1 [Comware-GigabitEthernet1/0/1] port link-aggregation group 1 [Comware-GigabitEthernet1/0/1] quit [Comware] interface g1/0/2 [Comware-GigabitEthernet1/0/2] port link-aggregation group 1 [Comware-GigabitEthernet1/0/2] quit [Comware] interface bridge-aggregation 1 [Comware-Bridge-Aggregation1] port link-type trunk [Comware-Bridge-Aggregation1] port trunk permit vlan 10 [Comware-Bridge-Aggregation1] quit The link aggregation is failing between the HP ProVision and HP Comware switches. Which solution solves this problem? A network administrator is examining the routing table on an HP Comware switch. The network administrator sees two routes, 10.1.1.0/24, with the same neighbor's address (10.1.1.1). What would create this result? What are the participants in the 802.1X authentication process? (Select two.) A network administrator needs to restrict access to the console port of an HP Comware switch. The initial access should prompt for a username and password. Which configuration should the network administrator implement? A network administrator is examining the routing table on an HP Comware switch. The network administrator sees two routes. 10.1.1 0/24, with the same neighbor's address (10.1.1.1). What would create this result?