640-692 - Supporting Cisco Routing & Switching Network Devices v1.0 Exam
Go back to Cisco
How many questions are there on the 640-692 exam?
There are 60-70 questions on the 640-692 exam to be completed in 90 minutes .
How long is the 640-692 exam?
The 640-692 exam is 90 minutes to complete 60-70 questions.
How much does the 640-692 exam cost?
The 640-692 exam is $300. The exam provider is Pearson Vue and you can register for the exam on their website.
What is the best way to study for the 640-692 exam?
The best way to study for the 640-692 exam is to practice at Exam.com.
Which three of the following statements are true about a smart jack? (Choose three)
It provides signal conversion.
It regenerates the signal to compensate for signal degradation from line transmission.
It provides loopback testing.
Which layer of the IOS model defines how data is formatted for transmission and how access to the physical media is controlled?
What are two possible causes if an Ethernet interface is up and the line protocol is down? (Choose two)
There is a speed or duplex mismatch with the remote device
There is a Layer 2 mismatch in the encapsulation type
Which two of the following statements are true? (Choose two)
The Cisco logo, old or new, can be found on the front bezel of all Cisco rack-mountable or desktop products.
At the network module level, the model number is the same as the part number.
Which command indicates the amount of memory (NVRAM, RAM, and flash) in a Cisco device?
From a Windows command prompt, which command displays the local IP address of a computer?
Which interface card is an encryption module?
Which command displays the configuration register setting?
Which two of the following are component of WAN connection? (Choose two)
Which three of the following statements are true about a router? (Choose three)
It interconnects multiple networks together.
It chooses the best route for your data to travel.
It divides a network into separate broadcast domains.
When using a modem to provide out-of-band access to a Cisco router, which cable type is used to connect the wall jack to the modem?
RJ-11 to Rj-11
Which command sends an echo request packet to the largest host and then waits for an echo response message?
Which type of memory stores the decompressed form of the Cisco IOS software and the running configuration?
The colored wires at one end of the cable in the reverse sequence of the colored wires at the other end of the cable. Which cable does this describe?
What are two ways to open a command prompt session on a Windows-based computer? (Choose two)
Click Start > All Programs > Accessories > Command Prompt
Click Start > Run. Enter cmd and click OK
Which of the following best describes the port on a laptop that is used to connection to an Ethernet port on a Cisco Switch?
Which of the following best describes the cable that is used to connect a laptop to the Console port on a Cisco router?
Which two pieces of information can be determined about a neighbor device from the CLI command show cdp neighbor? (Choose two)
Which port displays the bootup process on a Cisco device?
Which two of the following are true? (Choose two)
SSH is a protocol that provides a secure remote access connection to network devices.
A Telnet network management connection is dropped when a router reboots.
Which two pairs of LAN Ethernet devices use an RJ-45 Straight-through cable? (Choose two)
Switch to router
Switch to server
Which type of memory is necessary for a router to boot?
Which three pieces of information about a device can be seen from the show version command? (Choose three)
What does Cisco use for Return Materials Authorization (RMA) tracking of field-replaceable parts?
Which bits represent the boot field in the configuration register value?
lowest four bits
Which command initiates copying the saved configuration of a Cisco device to a TFTP server?
copy startup-config tftp
While performing password recovery on a Cisco device, the configuration register should be which value in order to bypass loading the startup configuration?
Which windows-based text editor is preferred when working with a simple text document such as a Cisco configuration?
A null modem cable uses which adapter type?
Which two modules can be plugged into internal advanced integration module (AIM) slots on a Cisco router? (Choose two)
Virtual Private Network Module
Intrusion Detection System Module
Which type of memory stores the startup configuration file for the Cisco device?
Which two of the following are installed fiber-optic connectors? (Choose two)
TFTP is a simple protocol files, such as a Cisco IOS or configuration file, from one device to another. Which device cannot be configured to be used as a TFTP server?
Which of the following best describes the cable that is used to connect a laptop to an Ethernet port on a Cisco router?
Which two commands are used to set the configuration register value? (Choose two)
Which type if memory is used to permanently store the Cisco IOS software?
Which of the following is a DTE device?
Which two commands display the saved configuration file? (Choose two)
Which command initiates the transfer of a Cisco IOS image over IP from ROMMON?
Which router can be used for disk-in-access to the router CLI management purposes and does not usually pass normal network traffic?
What are two features that are associated with single-mode fiber-optic cable? (Choose two.)
a single strand of glass fiber
carries higher bandwidth than multimode fiber
Which two of the following statements are true about a switch? (Choose two)
It is a data link layer device.
It reads the destination MAC address to forward traffic out the appropriate port.
Which command can be used to identify the serial number of a Cisco router?
What are two ways to open Microsoft Notepad on a Windows-based computer? (Choose two)
Start > Run Enter Notepad and 'Ink OK
Start > All Programs > Accessories > Notepad
Which command initiates the copy of an IOS image to a Cisco device?
copy tftp flash
When using a modem to provide out-of-band access to a Cisco router, which cable is used to connect the modem to the router?
DB-25 to RJ-45
At the interface configuration prompt, which command returns you to the main configuration prompt?
What is the default operating mode you are initially logging into a router?
Which address facilitates the routing of packets over an IP network?
Which of the following best describes how to assign a static IP address to the Ethernet port on a computer?
From Network Connections, double-click Local Area Connection. Click Protocol (TCP/IP). Click the properties, click the use the Following Address button, and then configure the IP information.