210-065 - Implementing Cisco Video Network Devices (CIVND)
Go back to Cisco
How many questions are there on the 210-065 exam?
There are 55-65 questions on the 210-065 exam to be completed in 75 minutes .
How long is the 210-065 exam?
The 210-065 exam is 75 minutes to complete 55-65 questions.
How much does the 210-065 exam cost?
The 210-065 exam is $300. The exam provider is Pearson Vue and you can register for the exam on their website.
What is the best way to study for the 210-065 exam?
The best way to study for the 210-065 exam is to practice at Exam.com.
A customer wants to record Cisco TelePresence conferences with the ability to alter the video format and add captions. Which two products are recommended to accomplish this goal? (Choose two.)
Media Experience Engine
TelePresence Content Server
A network administrator is asked to configure a video conference using the Cisco TelePresence MCU 5300. There is a requirement for participants to start with the same layout when joining the conference. How can this goal be accomplished?
Configure a custom layout and apply the layout to all new participants.
A Cisco TelePresence VCS displays this alarm: "Root password is set to default." How can this security warning be addressed?
Use SSH to log in to the Cisco TelePresence VCS as Root, issue the command passwd, and enter the new password when prompted.
Management wants to modify Cisco TMS to allow users to configure the call behavior with their associated devices and dial from a single ID. Which feature needs to be enabled and configured?
A new Cisco TelePresence MCU 5300 is being installed. The customer requested a static IP address to be configured on this device. Which two methods address this request? (Choose two.)
From the MCU console, issue the command static A ip-address netmask default-gateway.
From the web interface, use the Network > Port A menu options.
Which Cisco TelePresence Multipoint Control Unit Layout view mode gives prominence to one conference participant over the other conference participants while still allowing conference participants to view multiple participants at the same time?
enhanced continuous presence
Which codec is most suitable for a video streaming solution?
Management would like to set up a permanent recurring Cisco TelePresence meeting where the team would dial into to a preconfigured number. Which meeting type should be used?
A Cisco TelePresence EX Series desktop endpoint failed to register to a Cisco VCS. The SIP status shows "Failed: 403 Forbidden" in the endpoint's web interface. What is the first thing that should be checked in the endpoint configuration settings?
Verify that the correct SIP authentication credentials have been configured.
A desktop video endpoint is needed that can support a PrecisionHD camera design and a built-in display, and is Bluetooth-ready and multisite-capable. Which desktop endpoint supports all of these requirements?
A technician has installed and powered on a Cisco TelePresence MCU 5320 and is connected via the console port. The technician needs to determine the IP settings that were automatically assigned via DHCP. Which command should be entered?
Which two of these support an ad-hoc conference call? (Choose two.)
Cisco TelePresence Multiway with Cisco TelePresence Multipoint Control Unit and Cisco TelePresence Video Communications Server
pressing the conference button on a Cisco Unified IP Phone 8941 to conference in a third call
Which two of these can cause registration problems for a Cisco TelePresence Codec C40 endpoint running in H.323 mode? (Choose two.)
The IP default gateway address is incorrect for the endpoint.
The E.164 H323Alias has not been configured on the endpoint.
A network engineer wants to automate the monitoring of Cisco TelePresence TX systems. Which step should the engineer take first?
Configure SNMP on the codec.
When scheduling a multipoint conference, which three devices are required for the conference to be scheduled and completed successfully? (Choose three.)
Cisco Unified Communications Manager
multipoint control unit
video conferencing endpoints
You have been informed from the field that a new Cisco TelePresence video endpoint has been deployed with an IPv4 address of 172.28.254.45. You need to check for connectivity from the Cisco Unified Communications Manager server. Which command should be entered to check for network connectivity?
utils network ping 172.28.254.45
Which of these is the core component of the Cisco Video Surveillance product suite that handles recording and serving of video feeds?
Cisco Video Surveillance Media Server
Which of these needs to be enabled in Cisco Unified Communications Manager in order for the Cisco TelePresence System 500-32 to be able to share a presentation with a Cisco TelePresence System Codec C40 endpoint that is registered to a VCS?
Allow presentation sharing using BFCP
What is the importance of defining option 150 in the DHCP server for Cisco TelePresence endpoints?
It is the TFTP server IPv4 address where the video endpoint retrieves its configuration file while booting.
Which two issues does utilizing an IP network storage solution for IP video surveillance help overcome? (Choose two.)
large, expandable storage space
A network engineer wants to perform a factory reset on a Cisco TelePresence MX device from the CLI. Which command should be used?
xCommand SystemUnit FactoryReset
A Cisco TelePresence System 1300 Series endpoint is in the process of booting and the engineer notices a red "X" on the screen for Step 6 in the boot process. What does this red "X" indicate?
There is an error with compact flash.
When placing a call from Cisco Jabber Video for TelePresence to the Cisco TelePresence System Codec C40, which FECCs are available?
Left, right, up, down, zoom-in, and zoom-out are all available.
Which statement is true about the Cisco TelePresence System 500-32 system regarding the HVAC needs for the room where it is installed?
The system does not require any additional requirements above the normal HVAC requirements for the room.
An immersive video room requires acoustic remediation because there is noticeable reverb present. What type of acoustic paneling does Cisco recommend to provide remediation?
NRC rating greater than 0.75
An engineer is configuring a Cisco TelePresence System endpoint for use with a maximum of six people in the room. Which table type should be configured when setting up cameras where two participants directly face the endpoint display?
An engineer wants to know if there is a way to determine the optical zoom of a Cisco TelePresence SX20 remotely. Which two methods will retrieve this information? (Choose two.)
From the CLI, run xstatus.
From the web GUI, choose Configuration > System Status > Camera.
What is the main difference between Cisco Jabber and Cisco Jabber Video for TelePresence?
Cisco Jabber registers to the Cisco Unified Communications Manager, whereas Cisco Jabber Video for TelePresence registers to the VCS.
A large company wants to procure video conference devices that allow multipoint conferences from C-Series and immersive endpoints that are registered to a Cisco VCS and Cisco Unified Communications Manager. Which two components meet the requirements of this company? (Choose two.)
Cisco TelePresence Server registered to Cisco VCS
Cisco TelePresence Multipoint Switch trunked to Cisco Unified Communications Manager
Which statement is correct regarding the difference between Multisite and Multiway conferencing?
Multisite requires the Multisite options key to be installed and configured at the endpoint, whereas Multiway requires a Cisco TelePresence Video Communications Server and a centralized multipoint control unit.
A network engineer wants to quickly view any issues that may exist for a newly deployed Cisco TelePresence SX20 codec. To which location in the codec web GUI should the engineer navigate to find this information?
Diagnostics > Troubleshooting
A Unified Communications engineer wants to configure a Cisco TelePresence SX endpoint using static IP addressing to use a different TFTP server. Which path will allow the engineer to complete this configuration?
Configuration > System Configuration > Provisioning > Set the External Manager Address
When connecting to a pan-tilt-zoom camera to a C-Series codec, what type of cable must be used for camera control?
a VISCA cable (DB9-to-RJ45)
To which Ethernet port on a Cisco TelePresence System (500/1x00/1300/3xx0) endpoint would a technician need to connect to manually assign a static IP address for first-time setup?
auxiliary network port
Cisco Video Surveillance Video Encoder cards perform which function?
the ability to use existing analog equipment with an IP-enabled video surveillance system
Which MCU supports the use of a lobby screen?
How would an administrator reset a Cisco VCS Control appliance to the default configuration?
Via the CLI, log in as root and issue the factory-reset command.
A user is currently on a Cisco TelePresence call using a Touch 8 device and would like to change the local screen layout so that the active speaker is in full screen and the other participants are smaller within the picture. Which layout option should the user choose?
A network engineer is setting up a Cisco TelePresence Content Server. The customer requires live streaming, but does not have a streaming server. Which media should be configured to stream locally from the TelePresence Content Server?
Which Cisco Video Surveillance product contains the Cisco Video Surveillance Encoding Server?
Cisco Video Surveillance Operations Manager
A customer has a data and VoIP converged network and would like to add video to this network. Which two key QoS elements should be included in the new network design? (Choose two.)
Configure bandwidth management features to smooth bursty traffic and mitigate end-to-end congestion.
Apply bandwidth control features that will guarantee bandwidth for the maximum possible amount of video traffic.
On a Cisco C-Series codec, where would a technician go to configure the wallpaper?
Configuration > Personalization
Which function does a Cisco TCS recording alias perform?
It provides a dialable alias that will trigger a TCS recording workflow.
The firmware for the primary codec of a Cisco TelePresence System 3010 is being upgraded. Which codec CLI command could be used to check on the progress of the update?
show upgrade detail
What is the main difference between a Cisco TelePresence Multipoint Control Unit and a Cisco TelePresence Multipoint Switch?
The Cisco TelePresence Multipoint Control Unit is a hardware bridge. The Cisco TelePresence Multipoint Switch is a software bridge.
A technician is trying to pair a Touch 8 with a Cisco TelePresence SX20 endpoint, but the codec is not automatically listed in the touch panel. What are two possible reasons for this behavior? (Choose two.)
The codec and the Touch 8 are on separate subnets.
Pairing visibility mode is not active on the codec.
A technician is trying to troubleshoot real-time call information from the CLI of a VCS. Which command should the technician enter?
The user of a Cisco TelePresence MX300 wants to control the far-end camera of any video conference participant. Which control device and function is used to control the far-end camera?
Tap on the image of one of the participants using touch control.
A video conference user that is connected via a Cisco TelePresence Codec C40 to a conference that is hosted on a Cisco TelePresence MCU 5300 would like to switch the local layout view. Which two options describe how to switch the local layout view without affecting the view of remote users? (Choose two.)
Use the Participant settings from the MCU 5300 web interface.
Use the Call Control settings from the codec web interface.
Cisco TMS is unable to manage endpoints and an engineer is required to capture logs to determine the cause. What is the menu path that the engineer should follow to capture and download logs from Cisco TMS?
Administrative Tools > TMS Server Maintenance > Download Diagnostic Files